1911 Beta

by **linuslolz** » Sat Jun 25, 2011 11:14 am

http://chicago.craigslist.org/chc/sys/2460664901.html just because its HD. And its unused.

by **kirk** » Sat Jun 25, 2011 10:19 am

linuslolz wrote:"The Samsung SyncMaster P2250 LCD monitor looks great and performs reasonably well, though it’s a little pricey when factoring in the lack of an HDMI input." ~ pcworld.

"Snazzy looks, good color reproduction, touch sensitive buttons, solid build, easy to setup

A bit pricey, no HDMI, color gamut is not wide enough" ~ techtree.

http://www.techtree.com/India/Reviews/S ... 630-1.html

http://www.pcworld.idg.com.au/review/mo ... 250/325318

For an extra $25, would it be worth going with that one rather than the one Sean posted above, which is used (I believe)?

I feel like it would, no?

by **linuslolz** » Sat Jun 25, 2011 9:17 am

"The Samsung SyncMaster P2250 LCD monitor looks great and performs reasonably well, though it’s a little pricey when factoring in the lack of an HDMI input." ~ pcworld.

"Snazzy looks, good color reproduction, touch sensitive buttons, solid build, easy to setup

A bit pricey, no HDMI, color gamut is not wide enough" ~ techtree.

http://www.techtree.com/India/Reviews/S ... 630-1.html

http://www.pcworld.idg.com.au/review/mo ... 250/325318

by **kirk** » Sat Jun 25, 2011 9:03 am

What about this:

http://chicago.craigslist.org/chc/sys/2460664901.html

$25 more than I was hoping to spend, but if it's worth it, then I'm willing. Especially since it's unused/unopened.

by **linuslolz** » Sat Jun 25, 2011 7:01 am

Ill send you a 22 lcd, if you pay for shipping.

by **kirk** » Sat Jun 25, 2011 12:08 am

rehpyc wrote:http://chicago.craigslist.org/chc/sys/2458045035.html

Or, visit SD for the summer, and I'll sell you my old 19" LCD for cheap.

Or you could be nice and send it to me for free, you stingy fuck.

Did that help my case at all? Be honest.

I've e-mailed a few of these Craigslist bros. I'll add this one to the list.

by **rehpyc** » Fri Jun 24, 2011 10:43 pm

http://chicago.craigslist.org/chc/sys/2458045035.html

Or, visit SD for the summer, and I'll sell you my old 19" LCD for cheap.

by **unpro** » Fri Jun 24, 2011 4:55 pm

http://chicago.craigslist.org/search/sy ... maxAsk=100 >>> http://chicago.craigslist.org/chc/sys/2452468353.html

by **kirk** » Fri Jun 24, 2011 2:43 pm

It was the monitor. Now who wants to shop with me?!

http://chicago.craigslist.org/search/sy ... maxAsk=100

Input? Anyone?

by **Rambizzle** » Thu Jun 23, 2011 5:33 pm

needs a new cd-rom.

by **mogers** » Thu Jun 23, 2011 3:46 pm

Just find a free CRT monitor on Craigslist, or go buy a new LCD Monitor.

by **ohhhhbeeee** » Thu Jun 23, 2011 3:41 pm

why are ppl helping this faggot.

gtfo hipster doofus.

by **k4b00m** » Thu Jun 23, 2011 3:39 pm

Shouldn't it be on Digital or HDMI depending on your setup? try pressing the <-/source button on your monitor if you have one, to switch it. I bought a new monitor years ago because of that I thought it was broken lol. Maybe that's not your problem I didnt read everything in this thread, but good luck!

by **kirk** » Thu Jun 23, 2011 2:16 pm

Okay, even when the monitor isn't plugged in it does the same thing. I'll turn it on when it's not plugged into the PC itself, and it will show a dark screen with a box at the top left that says, "Analog" - after 2 seconds the whole screen turns black.

ALSO I had the graphics card replaced roughly a year ago by a shop, so I'm kind of thinking/hoping I don't have to get that done again.

Taking the monitor to a shop tomorrow to have it plugged in and checked out. They said they'll do it for free.

by **ward** » Wed Jun 22, 2011 2:29 pm

If a videocard fries it won't necessarily still be sending a signal. One of the computers we use at work had an ATI card fry in it and the monitor would just stay in power save mode when you turned the computer on.

by **sik** » Tue Jun 21, 2011 8:55 am

similar situation happened to me recently kirkland. removed my vid card and air dusted that shit and it works like new again. if a vid card fan does not operate at a certain speed then the vid card will turn off. try it brah. <3

by **scorch-** » Tue Jun 21, 2011 7:27 am

hellfire wrote:
alex kirk wrote:
hellfire wrote:1. Turn off your PC.
2. Unplug your power cable from your power supply & Unplug your DVI/AGP Cable from your PC.

Leave power on to your monitor (At this point your monitor should say " No cable Link, or Cable Undetected " )

3. Remove the side panel from your computer.
4. BOND yourself by touching your case to d-energize your components.
5. Carefully remove your video card, and then re-install it.

6.. Re-put everything back together/ and hope for luck
1) Why do I leave the monitor on while doing steps 3-6? Just to see if the message pops up and stays?
2) Lost me at step 4. I'm bad with computers, so, elaborate that one for me?
1 . If you unplug the monitor from your computer however leave power to it and turn it on, the screen should still be active.. unless its dead, then there will be no picture.

2. The VideoCard might have failed, when a VC fails they produce the same issues you are getting as well.

These steps are telling me which components are not functioning properly.

The GPU should be sending signal to the monitor whether it's on or not right? Doesn't sound like a GPU at all if the monitor screens up briefly when he powers it back on and then goes black.

You could test that more easily by plugging in to the integrated GPU on your motherboard (if it has one).

by **hellfire** » Tue Jun 21, 2011 1:09 am

alex kirk wrote:
hellfire wrote:1. Turn off your PC.
2. Unplug your power cable from your power supply & Unplug your DVI/AGP Cable from your PC.

Leave power on to your monitor (At this point your monitor should say " No cable Link, or Cable Undetected " )

3. Remove the side panel from your computer.
4. BOND yourself by touching your case to d-energize your components.
5. Carefully remove your video card, and then re-install it.

6.. Re-put everything back together/ and hope for luck
1) Why do I leave the monitor on while doing steps 3-6? Just to see if the message pops up and stays?
2) Lost me at step 4. I'm bad with computers, so, elaborate that one for me?

1 . If you unplug the monitor from your computer however leave power to it and turn it on, the screen should still be active.. unless its dead, then there will be no picture.

2. The VideoCard might have failed, when a VC fails they produce the same issues you are getting as well.

These steps are telling me which components are not functioning properly.

by **rehpyc** » Tue Jun 21, 2011 12:35 am

Correct, try taking the graphics card out and putting it back in. Also verify that the fan on the card is working.

By your description, it sounds like the inverter or power supply of the monitor has gone bad. Typically the backlight will show signs of dying prior to going out (ie slight flickering or slow in getting bright), but it's still a possibility.

by **kirk** » Mon Jun 20, 2011 11:18 pm

rehpyc wrote:1) Yes
2) Basically to ground yourself and release any static electricity before touching a hardware component

It could be your video card, it could be the monitor.. until you have one or the other to test, it's hard to say exactly what it is.

So just touch the side of the case, then deal with the graphics card (without touching anything else, I'm assuming, like the carpet), then re-test?

by **rehpyc** » Mon Jun 20, 2011 10:36 pm

1) Yes
2) Basically to ground yourself and release any static electricity before touching a hardware component

It could be your video card, it could be the monitor.. until you have one or the other to test, it's hard to say exactly what it is.

by **kirk** » Mon Jun 20, 2011 9:58 pm

hellfire wrote:1. Turn off your PC.
2. Unplug your power cable from your power supply & Unplug your DVI/AGP Cable from your PC.

Leave power on to your monitor (At this point your monitor should say " No cable Link, or Cable Undetected " )

3. Remove the side panel from your computer.
4. BOND yourself by touching your case to d-energize your components.
5. Carefully remove your video card, and then re-install it.

6.. Re-put everything back together/ and hope for luck

1) Why do I leave the monitor on while doing steps 3-6? Just to see if the message pops up and stays?
2) Lost me at step 4. I'm bad with computers, so, elaborate that one for me?

by **hellfire** » Mon Jun 20, 2011 9:39 pm

1. Turn off your PC.
2. Unplug your power cable from your power supply & Unplug your DVI/AGP Cable from your PC.

Leave power on to your monitor (At this point your monitor should say " No cable Link, or Cable Undetected " )

3. Remove the side panel from your computer.
4. BOND yourself by touching your case to d-energize your components.
5. Carefully remove your video card, and then re-install it.

6.. Re-put everything back together/ and hope for luck

by **unpro** » Mon Jun 20, 2011 8:01 pm

the crt i had since like 2001 finally died early last year after running basically that whole time at 100hz. used to share my comp with 2 other people constantly so it never even got a break. love me some viewsonic.

by **acetamino** » Mon Jun 20, 2011 6:47 pm

joeledmunds wrote:I had this happen to me during CAL-I playoffs and had to play on a laptop on a couch with a borrowed monitor on a coffee table. I had to get a new screen. :[

stopped reading after joel said cal-i

by **scorch-** » Mon Jun 20, 2011 6:39 pm

haha I'm still using the 21" CRT i bought in 2004.

by **unpro** » Mon Jun 20, 2011 5:35 pm

reasons like this are why i still use a CRT.

you know pretty much always you have like 5 years on a CRT even with running high refresh rates.

by **scorch-** » Mon Jun 20, 2011 5:23 pm

alex kirk wrote:
linuslolz wrote:Got any other cables?
Does the monitor go black after or before bios?
No other cables. It'll go black before and after bios. Immediately after the monitor shows picture, it'll go black. I'll turn it off and then back on again (post-bios), and same thing will happen. I can do this 100 times before or after bios and it'll be the same process: show a picture for a few seconds, then go black as though it's been unplugged.

Scorch - Do you have to replace the entire monitor, then? Or just a part within the monitor.

Dorito - Thanks, I'll be trying that one.

Kevin - You're welcome, for if my computer were operational, I would have crushed your face with the force of a thousand stallions.

I was just reading someone asking the same question. Depends on the how much your monitor is worth, but replacing the backlight is pretty expensive so it's probably better to just buy new if your monitor is already past warranty.

by **Avail** » Mon Jun 20, 2011 4:50 pm

This is what you get for pirating music!!!!!

by **kirk** » Mon Jun 20, 2011 4:29 pm

linuslolz wrote:Got any other cables?
Does the monitor go black after or before bios?

No other cables. It'll go black before and after bios. Immediately after the monitor shows picture, it'll go black. I'll turn it off and then back on again (post-bios), and same thing will happen. I can do this 100 times before or after bios and it'll be the same process: show a picture for a few seconds, then go black as though it's been unplugged.

Scorch - Do you have to replace the entire monitor, then? Or just a part within the monitor.

Dorito - Thanks, I'll be trying that one.

Kevin - You're welcome, for if my computer were operational, I would have crushed your face with the force of a thousand stallions.

by **stealthlol** » Mon Jun 20, 2011 4:20 pm

If you're scared to play us, Alex, just admit it.

by **joeledmunds** » Mon Jun 20, 2011 4:07 pm

I had this happen to me during CAL-I playoffs and had to play on a laptop on a couch with a borrowed monitor on a coffee table. I had to get a new screen. :[

by **dorito** » Mon Jun 20, 2011 4:05 pm

i was having something similar to this happening to me a while ago. i found out my video card was somehow coming loose from my motherboard. try taking your video card off then re-inserting it onto your motherboard.

by **scorch-** » Mon Jun 20, 2011 4:01 pm

"It sounds like the backlight within the LCD is about to die. I have encountered a few which did the same thing as you explain... The LCD seems fine for a minute and then goes black or displays very faint, dark text and images." similar situation with an LCD.

by **linuslolz** » Mon Jun 20, 2011 3:59 pm

Got any other cables?
Does the monitor go black after or before bios?

by **avenger** » Mon Jun 20, 2011 3:59 pm

youll probably want to find someone to snag a spare monitor from to try it, like others suggested (and obviously) it could be your monitor. i had a similar problem once when my video card burnt up.

by **kirk** » Mon Jun 20, 2011 3:53 pm

No other computers, monitors, or TVs that can help me.

by **linuslolz** » Mon Jun 20, 2011 3:48 pm

Try with another monitor.

by **defiance** » Mon Jun 20, 2011 3:48 pm

if you have a newish TV, hook the tower up to it using the same cables to narrow down the problem to the actual monitor. Then buy a new monitor!

by **aLpha.cn-[tang]** » Mon Jun 20, 2011 3:45 pm

How the hell do you break your computer so often?

by **kirk** » Mon Jun 20, 2011 3:41 pm

There I was minding my own business when my computer done brokened. Here's what happened:

1) Monitor randomly went black as though it had been unplugged.
2) I shut down and restart - picture comes back.
3) Within a few seconds, monitor is black again.
4) When I turn the monitor off and then back on again, it works. After about 2 seconds, however, it goes black again.

I turned off the computer and left it off for ~30 minutes because it felt warmish. I also disconnected all the monitor cables and reconnected. Still nothing.

So the monitor turns on, but quickly turns black as though it's being unplugged.

No other computers in the house where I can test the monitor.

Ideas, go!

Inb4 stealth says, "way to purposely break your computer to avoid playing DCN tonight."

Post a reply

Expand view Topic review: Fix kirk's computer.